After austempering, the microstructure of CADI contains austenite with high carbon. The proportion of austenite in ausferrite can influence mechanical properties, corrosion resistance and wear resistance. The test results show temperature and holding time greatly affect the amount of carbon-enriched austenite in CADI.

Figure 3 shows the influence of austempering temperature on the amount of carbon-rich austenite. As temperature increases, the austenite content increases gradually.

Figure 4 shows the influence of temperature on the impact toughness of CADI. When the temperature is below 446F (230C), the impact toughness remains steady. After that, the impact toughness increases with austempering temperature up to 554F (290C), after which it again flattens out.

Figure 5 shows the influence of austempering temperature on CADI hardness, which decreases as the temperature rises.

Figure 6 shows the influence of austenite content on the corrosive speed of CADI in faintly acidic, neutral and alkalescent liquids. The corrosive speed increases with a greater amount of austenite in all kind of media. When the content of austenite was about 22%, the corrosive speed reached its peak. After that, the corrosion speed decreased in faintly acidic and alkalescent liquid, while changing very little in neutral liquid.

Because austenite has a corrosive-resistant microstructure, the corrosive resistance of CADI should increase with the amount austenite. So why does the corrosive resistance decrease with an increase of austenite in range of 16-22%? It is possible the resistance to corrosion is related to a difference between needle ferrite carbon and austenite, but additional research is needed.

Overall, the corrosive speed of CADI is the highest in faintly acidic media, the lowest in weakly basic media and in the middle in neutral media. CADI has lower corrosive resistance in faintly acidic liquid and better corrosive resistance in weakly basic liquid.

The influence of austenite on the corrosion current density is shown in Figure 7. The corrosion current density of CADI increases with austenite. When the content of austenite reached 22%, the corrosive current density reached its apex. But as the austenite content of ausferrite increased, the corrosion current density decreased in faintly acidic and basic liquid, and remained steady in neutral liquid. According to a principle of electrochemistry, the corrosive resistance of a material decreases as its corrosive current density increases. CADI that contains 22% austenite was less resistant to corrosion.

With the use of an MLD-10 abrasive wear testing machine, CADI’s corrosive and abrasive resistances were researched with a dynamic load impact power of 1 joule, rotating speed of 200 RPM and impact frequency of 100 cycles per minute in three liquids with different PH values. A low chromium cast iron specimen was the control for the CADI samples.

As shown in Figures 8 and 9, as the content of austenite increased, the CADI specimens lost more weight due to corrosion and their relative abrasive resistance declined. In the weakly acidic and alkaline media, when the austenite content was in the range of 20-22%, the corrosive wearing weight loss was the highest and the relative abrasive resistance the lowest. When the austenite was more than 22%, the weight loss decreased and the relative resistance increased. In a neutral medium, corrosive resistance changed little when the austenite content was more than 22%.

The carbon-enriched austenite contributes to the abrasive resistance of CADI in two aspects. Austenite can transform into martensite under stress, so the surface hardness and abrasive resistance of CADI increases remarkably. Secondly, during the process of transformation from austenite to martensite, the increase of volume is accompanied in the wearing surface layer of specimen, which results in compressive stress on surface that can improve wear resistance.

During powder grinding in metallurgical, mining, cement and thermal power industries, production costs for abrasion materials and energy consumption are a large share of total expenditures. Considering the growth in China’s steel and iron industries, the requirement for iron ore is very large, about 40-50% of worldwide demand. From 2009 to 2011, China increased its production of crude steel from 568 to 680 million metric tons. The domestic iron ore production grew from 880 million metric tons in 2009 to 1.1 billion in 2011. Additionally, in 2012, cement production was about 2.2 billion metric tons, accounting for 60% of global consumption. In 2009, the consumption of abrasion-resistant castings was more than 3.5 million metric tons, with grinding balls used for 1.6 million metric tons. Mineral processing in iron and nonferrous ore accounted for 70% of all grinding ball expenditures.

Currently, grinding balls are made of low chromium cast iron, high chromium cast iron and forged low alloy steel. The characteristics of low chromium cast iron balls are low hardness, poor abrasive resistance, low impact toughness and low breaking points. High chromium cast iron balls have high hardness, good wear resistance in dry conditions, low wear resistance in a corrosive environment, low cost performance and low impact toughness. The characteristics of forged low alloy steel balls are low hardenability, low volume hardness, low corrosive resistance and poor abrasive resistance. A broken and spalling ball can reduce a grinding mill’s efficiency and productivity, while increasing energy consumption. In addition, many grinding balls used in China contain different amounts of chromium. Because chromium is in short supply in China, 90% of ferrochrome is imported. Therefore, the development of a ball with very low or no chromium and high abrasive resistance is imperitive.